all thread rod specifications pdf

TECHNICAL DATA SHEETTHREADED ROD

Threaded rod is often used along with a nut and/or square plate washer when embedded in concrete to achieve required pull out values. The ASTM A307 specification covers carbon steel bolts and studs ranging from 1/4" through 4" diameter.Threaded Rod Product Specifications Ram Pipe and PV35592 All Thread Rod Zinc 1/4 x 6" 20 60,000 INT/EXT A307 03 PV35593 All Thread Rod Zinc 1/4 x 10" 20 60,000 INT/EXT A307 03 PV35594 All Thread Rod Zinc 3/8 x 6" 16 60,000 INT/EXT A307 03 PV35595 All Thread Rod Zinc 3/8 x 10" 16 60,000 INT/EXT A307 03 PV35596 All Thread Rod Zinc 3/8 x 12" 16 60,000 INT/EXT A307 03Grades All Thread RodHowever, stainless steel all thread rod is often specified under a variety of ASTM specifications including A193, A320, and F593. The type of stainless steel desired for the project will be specified as a grade within the A193 and A320 specifications or as a alloy group and condition within the F593 specification.

Hardware Cooper Industries

ATR 18 5900(26.24)225(102.06) ATR All Threaded Rod. Available in 36 (91.4 cm), 72 (182.9 cm), 120 (304.8 cm), 144 (365.7 cm)lengths Safety Factor of 5 on recommended load Standard finishZinc Plated, Stainless Steel Type 304. B655 Rod Coupling B656 Reducer Rod Coupling.Technical Info All Thread RodThread Series All thread rod is manufactured in three different thread seriesUnified National Coarse (UNC), Unified National Fine (UNF) and 8 Thread Series (8UN). UNC thread is the most common designation for all thread rods. UNF thread is most often used for precision applications. 8UN thread is used specifically for grades under ASTM A193 and Threaded Rod, ASTM A193 B7, Zinc PlatedThreaded Rod, ASTM A193 B7, Zinc Plated The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order. If the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your status as an approved vendor.

Fastenal Product Standard REV 05

Page 1 of 2 Fastenal Product Standard REV 05 DateJanuary 12, 2017 TROD.B7.P Threaded Rod, ASTM A193/A193M and ASME SA193/SA193M, B7, Plain The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.HILTI ANCHOR ROD SPECIFICATIONS AND TECHNICAL 10 All carbon steel threaded rods are zinc plated in accordance with ASTM F1941 Fe/Zn 5 AN, with nuts and washers zinc plated in accordance with ASTM B633 SC 1 Type III. 11 HAS E B HDG rods hot dip galvanized in accordance with ASTM A 153. 12 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105 ksi Yield StrengthHILTI ANCHOR ROD SPECIFICATIONS AND TECHNICAL Hilti Anchor Rod Specifications and Technical Data 1 All carbon steel threaded rods are zinc plated in accordance with ASTM F1941 Fe/Zn 5 AN, with nuts and washers zinc plated in accordance with ASTM B633 SC 1 Type III. All hot dipped galvanized threaded rods, nuts, and washers are zinc plated in accordance with ASTM F2329.

HILTI ANCHOR ROD SPECIFICATIONS AND TECHNICAL

Hilti Anchor Rod Specifications and Technical Data June 2018 The following steel design information is for Hilti HAS threaded rods according to the material specifications on page 2, used in conjunction with Hilti adhesive anchors designed in accordance with ACI 318 Chapter 17.ALL THREAD ROD GRADE A193 B7 ITPALL THREAD ROD GRADE A193 B7 SUBMITTAL SPECIFICATIONS Abstract of ASTM A193 / ASTM A194 GradeCHROMIUM LYBDENUM (AISI 4140) DIMENSIONAL DATASizes 1 inch and smaller in diameter with the coarse thread series, and the 1 1/8 inch and larger in diameter with the 8 pinch thread series unless otherwise specified by the customer.Fastenal Product Standard REV 05Page 1 of 2 Fastenal Product Standard REV 05 DateJanuary 12, 2017 TROD.B7.P Threaded Rod, ASTM A193/A193M and ASME SA193/SA193M, B7, Plain The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order.

Threaded Rod, ASTM A193 B7, Zinc Plated

Threaded Rod, ASTM A193 B7, Zinc Plated The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order. If the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your status as an approved vendor.THREADED ROD, INCH SERIES Barnhill Boltthreaded rod, inch series tensile strength60,000 psi min threadscommercial nut fit similar to class 1a plain finish, zinc plated to meet astm f1941 fezn3a, hot dip galvanized to meet astm a153 tensile strength [nc threads] tensile strength [nf threads] size psi pounds size psi pounds 1/4 20 60,000 1900 1/4 28 60,000 2180 5/16 18 60,000 Threaded rod Bolt DepotThreaded rod; Material. Stainless steel 18 8. A corrosion resistant steel alloy. The most common stainless steel for general hardware use. Stainless steel 316. A corrosion resistant steel alloy. A highly corrosion resistant grade of stainless steel. Ideal in salt water and chlorine environments. More expensive than 18 8. Zinc plated steel

All Thread Rods Portland Bolt

Technically, all thread rod made from A36 steel should be ordered to a fastener specification such as A307 Grade A, A307 Grade B, or F1554 Grade 36. The appropriate fastener specification will depend on the application.Grade 8 All Thread Rod Weaver Distributing©2020 Weaver Distributing 10705 West Orchard Yakima, Washington 98908 Phone509 965 2430 Fax509 966 8030 Toll Free1 800 734 1990Acme Threaded Rods McMaster CarrChoose from our selection of Acme threaded rods, including lead screws and nuts, precision lead screws and nuts, and more. In stock and ready to ship.

Rod, Studs, Bent Bolts All America Threaded Products AATP

LEARN MORE MATERIAL OPTIONS We are proud to carry a variety of material options. Learn more about our product offerings and request a quote below. BROWSE PRODUCTS YOUR SUPPLY PARTNER FOR DOMESTIC THREADED PRODUCTS We manufacture a wide range of quality threaded products including rods, studs, anchor bolts, u bolts and custom specials.146 Cont. Threaded Rod Anvil InternationalDescription. Size Range1/4" through 1 1/2" Stocked in six, ten, and twelve foot lengths. Other even foot lengths can be furnished to order. MaterialCarbon steel or Stainless Steel Gr 304 ThreadsNational Coarse (USS), rod threaded complete length. FinishPlain or Zinc Plated (Hot Dip Galvanized optional) Maximum TemperatureZinc Plated 450F, Stainless Steel 650° FThreaded Accessories Cooper IndustriesFig. 99 All Threaded Rod Cut To Length Size Range3/8" 16 thru 3" 4 rod MaterialSteel FunctionRecommended for use as a hanger support in hanger assemblies. Rod is threaded on both ends with right hand threads of the length shown. Also available with left and right hand threads specify Fig. B3205L when ordering.

Everbilt 3/4 in. x 36 in. Zinc Threaded Rod 802277 The

Threaded rods are metal rods with continuous threading Threaded rods are metal rods with continuous threading and no head or fashioned tip. Commonly used as anchor Bolt, clamps, hangers and U bolt. They are available in a variety of diameters, lengths and finishes.TECHNICAL DATA SHEETTHRA ROSPECIFICATIONS ZINC PLATED Grade A Headed bolts, threaded rods and bent bolts intended for general applications. Grade B Heavy hex bolts and studs intended for flanged joints in piping systems with cast iron flanges. Grade C* Nonheaded anchor bolts, either bent or straight, intended for structural anchorage purposes.

Get In Touch With

We receive enquiries in English, Español (Spanish), Русский язык (Russian), Français (French) and العربية (Arabic). Our professional team will reply to you within 24 Hour. Please feel free to contact us!