EN 1.0503 Material C45 Steel. EN 10083 2 C45 steel (EN 1.0503) is a high strength medium carbon quality steel. Due to poor hardenability, C45 material is generally used in a normalized condition, and when the mechanical properties are required to be high, C45 / 1.0503 SteelNumber Chemical composition Non alloy quality steel Chemical composition of steel C45 (1.0503), Standards of steel C45 (1.0503) Mechanical Properties of steel C45 (1.0503) Equivalent grades of steel C45 (1.0503) steel C45 (1.0503) Tensile Strength, Elongation, Proof strength , HardnessC45 Steel DIN 17200 EN 10083 Standard quenched and C45 carbon steel ground bar can also be supplied, providing a high quality tool steel precision ground tool steel bar to your required tolerances. DIN W N R C45 steel is also available as Ground Flat Stock / Gauge Plate, in standard and nonstandard sizes.
C45 EN 10083 2 (Euronorm) Reduction of area> 40 % Diameter> 40 mm ; Yield Strength> 370 MPa Tensile Strength630 780 MPa Elongation> 17 %What is the shear strength value of C45 material? steel Ssu = Approx 0,75 x 800=600 MPa..(2) So, shear strength value of C45 material will be in between 450 to 600 MPa.C45 Round Bar AISI 1045 DIN 1.1191 Otai Special SteelSteel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570
C45 EN 10083 2 (Euronorm) Reduction of area> 40 % Diameter> 40 mm ; Yield Strength> 370 MPa Tensile Strength630 780 MPa Elongation> 17 %What is the shear strength value of C45 material? steel C45 Steel properties.:. Tensile strength 600 800 MPa Young's modulus 210000 210000 MPa Elongation 16 16 % Yield strength 340 400 MPa. Ultimate Tensile strength (600 800) MPaC45E / 1.1191 SteelNumber Chemical composition Non alloy quality special steel Chemical composition of steel C45E (1.1191), Standards of steel C45E (1.1191) Mechanical Properties of steel C45E (1.1191) Equivalent grades of steel C45E (1.1191) steel C45E (1.1191) Tensile Strength, Elongation, Proof strength , Hardness
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness. The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special C45 BEBON steelC45 steel plate, EN 10083 C45 steel plate, under EN 10083 standard, we can regard C45 steel plate as high carbon steel.. C45 steel plate is one mainly of high carbon steel,EN 10083 C45 steel plate is for quenching and tempering. Technical delivery conditions for non alloy steels,these steels are for general engineering purposesMaterial specification sheet Saarstahl C45Material specification sheet Saarstahl C45 Material No.1.0503 Former brand nameAFNORInternational steel gradesBSC45, 50CS, 080M46 C45, AF65C45, 1C45 SAE1045 Material groupSteel for quenching and tempering according to DIN EN 10083 C Si Mn P S Cr Mo Ni
ASTM A830 AISI 1045 Steel Plate, Carbon Steel 1045 Sheet, Carbon Steel 1045 Plate, C45 Sheet Exporter, UNS G10450 Carbon Steel Plate and Sheet, EN C45 Carbon Steel HR Plate, 1045 Plate, C45 / 1045 Hot Rolled Steel Plate, C45 1.0503 Cold Rolled Sheet, MS C45 Sheet, AISI 1045 Plates Manufacturers in Mumbai, India.SAE AISI 1045 (S45C, G10450) Carbon Steel :MakeItFromSAE AISI 1045 steel is a carbon (non alloy) steel formulated for primary forming into wrought products. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number. It can have a moderately high tensile strength among the wrought carbon or The World Material Free Online Material Information SS304 Grade AISI 304 Stainless Steel Properties, Composition, Density, Yield Strength, Thermal AISI 304 Grade Stainless Steel (UNS S30400) AISI 304 stainless steel (UNS S30400) is the most commonly used material in stainless steels, and is usually purchased in an annealed or cold worked state.
Q345 steel specificationQ345 steel belongs to 16Mn steel grade, usually it is produced in hot rolled state, hot rolled steel plate, hot rolled steel coil/sheet, it has comprehensive mechanical and welding property, as it shows good performance in structural purposes, it is widely used as welding structural part in manufacturing of ship, railway and vehicles, bridges, boiler, pressure vessel Grade 1074/1075 Steel McMaster CarrHardnessRockwell C45 (Hard) 1075 spring steel is easier to bend than 1095, but it has less bounce back after heat treating. It is often used for springs and shims.Table of material properties for structural steel S235 Nominal values of structural steel yield strength and ultimate strength. For structural design according to Eurocode 3 (EN1993 1 1), the nominal values of the yield strength f y and the ultimate strength f u for structural steel are obtained as a simplification from EN1993 1 1 Table 3.1, which is reproduced above in tabular format.
C60 steel is an unalloyed medium carbon engineering steel which has 0.57% 0.65% Carbon as per EN10083 standard.It has characteristics similar to that of C55 carbon steel which has high hardness and high strength after hardening.C60 is difficult to weld,and machinability is poor due to high carbon content.This steel is generally supplied in an untreated or normalised condition.Steel Foil McMaster CarrAlso known as mild steel, low carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that dont require high strength, such as fixture clamps, mounting plates, and spacers. This material can be surface hardened with heat treating.
We receive enquiries in English, Español (Spanish), Русский язык (Russian), Français (French) and العربية (Arabic). Our professional team will reply to you within 24 Hour. Please feel free to contact us!